GE Healthcare c Anesthesia Machine Technical Reference Manual Software Revision 1.x Approved −12−9 EET Junmin Ji (Rick) M c Product Data Sheet – GE Healthcare c Familiar, reliable, GE – with over years experience in anesthesia and quality leadership? 53 cm/21 in Depth: 40 cm/16 in Side of machine: cm/45 in Height: The c is the ideal solution for customers seeking an affordable, reliable and easy-to-use anaesthesia system. The c is designed and manufactured in.
Gas flows from the bellows, through the absorber, the EZchange, and through a unidirectional valve inspiratory check valve to the patient. Before testing the system, ensure that: Used equipment may contain blood and body fluids.
Unscrew the valve seat A from the vent engine manifold. Back out the system switch mounting screws just enough to allow the knob collar to be released.
Ensure that all cylinder and pipeline gauges read zero before proceeding. Back out the selector macine mounting screws until the tips are flush with the face of the mounting casting.
Multipurpose Anaesthesia Machine- 9100C
Replace the free breathing flapper valve. Turn all flow controls full clockwise zero flow.
Using a 13mm open ended wrench, remove the vaporizer pressure relief valve by turning counterclockwise. Place the display module face down on a protected surface. Direct access to ventilator parameter settings? If the pressure rise is more than 10 cm H2O, replace the 10 cm H2O aanesthesia weight and seat. Test the apnea and low airway pressure alarms: Control Sample Board under tabletop.
Multipurpose Anaesthesia Machine- C – Yoga Enterprises, Pune | ID:
Reinstall the breathing system. Set the ACGO selector switch to the breathing system, if equipped. Mississauga, Ontario Australia Pty. The apnea alarm occurs after 15 seconds.
Navigator Applications Suite A digital clinical decision support tool that puts relevant, reliable, and predictive information at your fingertips. The small port is the port closest to the patient connection.
In this section To ensure proper operation, the c Ventilator includes several tests that run automatically self tests and a series of menu pages that a qualified service person can use to test, calibrate, or troubleshoot ventilator related components in the c anesthesia machine Service Mode.
Verify that AGSS is operating if equipped. Disconnect the test device. Ensure that all cylinder and pipeline gauges read zero before check valve proceeding. Remove the absorber, the vaporizers, gas cylinders, drawers and all auxiliary equipment. Reinstall the transparent covers.
If the machine includes only some of the optional features, access the Key Code Generator web site to obtain the appropriate anestnesia features Key Code.
MOPV pressure relief valve test Section 6. As circuit pressure approaches the pressure placed on the APL disc, any additional pressure will cause the disc to lift and gas vents to the scavenging system. Install a anestehsia cylinder in the cylinder supply to be adjusted. APL or pop-off valve. Replace the large rear upper panel. Regulator D Also inspect the two o-rings that seal it to the manifold.
Get best deals for coconut. Verify proper alignment of the knob with the setting indicators.
Pipeline and cylinder tests Section 3. Any redistribution mchine reproduction of any or all of the contents in any form without the prior written permission of General Electric Company is expressly prohibited.
Remove the two mounting screws from the O2 supply switch. Verify that parts are free of dust and dirt. O2 pipeline inlet Use a safe, approved procedure to remove and collect the agent. Low flow, low vacuum Low flow, low vacuum Low flow, low vacuum Flow Sensor Positive Section 4. Disconnect the pipeline supplies and close all cylinder valves if equipped. Excess gas vents to the scavenging system through the pop-off valve and the exhalation valve.
A pressure decrease large enough to see on the gauge indicates an unacceptable leak. Help Center Find new research papers in: Keyboard front panel 6. Slide the tabletop forward and lift to remove. If the cylinder supply being tested is N2O, connect a source of O2 to pressurize the balance regulator and allow N2O to flow.
Push hard for a good seal. The bulb should not inflate in less than 60 seconds. Leave the patient pressure gauge end open. Do not use a test plug that is small enough to fall into the breathing system.