AUTRONICA BS-100 PDF

  • August 22, 2019

BS loop interface – BSD AutroSafe interactive detection system. Product datasheet. P-BSD/CGB, Rev. D, Protecting life. Products 1 – 20 of 33 Autronica BS , BS 90 and BS 60 fire alarm systems supplied, programmed and serviced. 3. Autronica Fire and Security AS. Contents. Please observe! This handbook contains installation instructions for fire alarm system BS DYFI ready designed.

Author: Kagazragore Tugami
Country: Malta
Language: English (Spanish)
Genre: Marketing
Published (Last): 2 June 2005
Pages: 319
PDF File Size: 13.10 Mb
ePub File Size: 3.36 Mb
ISBN: 835-5-24166-418-9
Downloads: 28057
Price: Free* [*Free Regsitration Required]
Uploader: Shaktitaur

Any international shipping and import charges are paid in part to Pitney Autronida Inc. If one or more addresses are still in alarm condition after the RESET procedure, an operator acknowledge is required to have these addresses disabled. Crank the ribbon around by means of the adjusting wheel to be sure that it runs correctly.

Please allow additional time if international delivery is subject to customs processing. Controls from customer data. The message will appear when the door is closed.

BS-100 loop interface BSD-330

On the BS control panel the fault message will appear in the display. Seller assumes all responsibility for this listing. Check that the ribbon is in the correct position in the ribbon slot. Subject to credit approval. Self-diagnosis of “fault” condition. ASAP on 2-wired current loop. Only the control outputs on the BS control panel which registered the fire alarm will be activated. Item sold as it is as seen in pictures. All detectors connected to the same loop have the same DYFI-filter constant.

  ALTKORN STRATEGIA MARKI PDF

Tested and complies with BS part 4:! Alarm delay T1, T2autgonica section 3. Numbers of restarts of the loop processor since last reset of the control panel.

AUTRONICA BS DYFI DYNAMIC FILTER PROCESS ALARAM FIRE DETECTION SYSTEM | eBay

Delivery times may vary, especially during peak periods. Both the alarm- and control-outputs are tested simultaneously. If this lamp lights on one of the BS control panels, it will also light on the BU-units.

Service Password protected on service level For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

Status will now be updated. The address A may be the individual receiver and the address B may be a group of receivers.

Additional modules can be added to allow a total of 16 loops addresses. Postage cost can’t be calculated. Fit the printer as shown with the paper roll at the bottom ensuring that the paper is fed through the slot in the panel face.

Earth fault monitoring of AK-output. New functions in Solas and DK. Prewarning output on the EA- will be activated output L Learn more – opens in new window or tab.

Location of the finger screw on the printer F: The internal clocks of all control autroica are independent and must be set individually. The letter given in the display means: Programmable outputs from 1 to are handled by BSJ modules.

For additional information, see the Global Shipping Programme terms and conditions – opens in a new window or tab. All new data will now be stored in the battery-RAM and will remain in the system even in the event of a power failure.

  KAUPEENA PANCHAKAM TELUGU PDF

The baud rate must be the same for all fitted loops.

Autronica BS Fire Alarm Control Panel DYFI BS | eBay

Sell now – Have one to sell? Contact the seller – opens in a new window or tab and request a postage method to your location. BUP is installed on the rear side of the display panel door. The current stored analogue value of the detector equal to ATS value. Skip to main content.

Setting of DIP-switch S1 elements 3 to 8. Changing of output controls, alarm outputs and disabling groups are password protected on service level 2.

Default delay time is 2 min. Add to watch list. Payment must be made within bbs-100 days from the winning day.

Watch list is full. Monitoring of all field devices and alarm path.

null | BS-100 DYFI – Fire Alarm Engineers

All switch elements on S1 and elements no. The table on the next page gives the positioning of the autrpnica both on S1 and S2. All disabled loops must be restored after ending the servicefunction. Close the control panel inner door.

Select a valid country. Report item – opens in a new window or tab.