The Uniden Bearcat BCT15X is the follow-up to Uniden’s premier analog mobile scanner, the manual for the radio is contained on a CD-ROM, in PDF format. DImage_/Manual/ (1 of 3)5/26/ .. This page applies to the following scanner(s): BCDXT BCT15X Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. View and Download Uniden BCT15 owner’s manual online. scanner radio with You can adjust the level of the following tones: Key Beep, BearTracker Alert.
To select both press HP 3 times. If the Motorola system has priority channels, and you assign one of those TGs bercat priority in the scanner, then when one of those channels becomes active, the scanner will jump to it even if it is on a different system voice channel i.
Alert Only – the scanner immediately sounds a weather alert siren when it detects the Hz weather alert tone, then opens the squelch and remains on the weather channel. Operation Before you apply power, there are a few basic operations to get the scanner ready. To confirm and delete all locked-out frequencies, press If no frequencies are locked, you see Nothing Locked Press Any Key.
There are links to refer you back here while you are programming. Then see Creating Sites. If the frequency has already been stored, the scanner continues to search. If the frequency is already stored in the group, ‘ Frequency Exists Accept? Head – Indicates the selected heading to the designated Dangerous Crossing from any direction. The only things you will be able to scan right out of the box are the preprogrammed states in the scanner.
See Editing a Custom Search first. You can also set the scanner to Auto Store Close Call hits. A negative delay will force a resume after that number of seconds. Read the reviews for each at the site. With this feature Offwhen the scanner detects a Close Call signal while scanning, the scanner does not override the current audio.
To toggle Alert Mute on or off temporary: For example, some of these action are required for basic programming or menu options. This fine-tunes the scanning operation and makes it that much enjoyable. Press MENU twice to return to the site menu. You need tone-out setup information from the agency you wish to monitor.
During service search, the scanner searches starting with the lowest frequency in the search range you select to the highest frequency in the range. Removing The Display Sticker Internal brackets Removing the Display Sticker Before you use the scanner for the first time, remove the protective plastic film over the display. To check for a repeater frequency on a conventional channel Hold on the channel.
With Key-Safe Mode you are stuck with just the last mode the scanner was in when you turned off the radio i. Edit Name If you do not enter a channel name, the scanner displays the frequency for conventional systems or the talk group ID for trunked systems when it stops on a channel.
This will give you ‘ Nothing to Scan ‘ in the display. Performance is increased with higher transmit power, receive antenna tuned to the target band, and a low background RF level. While in Review Location Mode: To clear a character or enter a spacepress. Repeater systems use two frequencies: I have included links to other information in the Wiki not relevant to the operation of the scanner so you can still find the rest of the info such as specs, weather event codes, deciphering trunked systems, etc.
Easier to Read BCTX Scanner Manual
Set Serial Port allows you to set the baud rate for the front and rear serial ports. Car Two is driving Car One east. You will not hear any audio in this mode.
Refer to the left illustration that follows, showing the Removal Keys. You can beearcat number tags to channels even if the system does not have a number tag but, without a system number tag, you can only navigate to these channels while holding or scanning in that system.
Cloning to clone copy data from one same scanner to another, use one of the included data cables to connect the two scanners.
Press , , or  to begin searching the range set when you btc15x up and assigned one of these keys to a selected search range. For an entire county, use 0.
When the transfer is finished, both scanners display a ‘ Complete ‘ message. Max IDs per Talkgroup. The blue light flashes with a Close Call hit.
Set Hold Time sets in seconds the amount of time the scanner will scan the system before moving on to the next bearfat. Conventional Display Mode 2. See checking Firmware Version. Thanks to the Radio Reference. The default setting is unlocked. At ‘ New Sys Name? See Edit Service Search first. While Scanning or Searching with Close Call Override set to Offwhen the scanner detects a Close Call signal, the scanner does not override the current audio.
Uniden BCT15 Owner’s Manual
Enter the data frequency. Nothe channel number tag, then MENU. Set State allows you to add the site to the Bear Tracker system so you can listen to it when you select your ‘State’.
The BCT15 uses a similar method to turn on and off scanning sites and systems. To search for tones, leave the tones for A and B at 0.