ISO 11992-4 PDF
ISO is a CAN based vehicle bus standard by the heavy duty truck industry. It is used for ISO Part 4: Diagnostic communication. Reference number. ISO/FDIS (E). STANDARD. ISO/FDIS. DRAFT. RECIPIENTS OF THIS DRAFT ARE INVITED TO. ISO. First edition. Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles —.
||16 November 2010
|PDF File Size:
|ePub File Size:
||Free* [*Free Regsitration Required]
A further service request will be rejected. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
This bit shall be set to ‘1’ and latched if a malfunction is DTC 111992-4 on the current or previous detected during the current monitoring cycle.
Incorrect has too many pulses 3A16 3B16 — 3F16 — This sub type is used for failures where the server measures too many pulses e.
BS ISO 11992-4:2014
A ConfirmedDTC does not always indicate that the malfunction is necessarily present at the time of the request. In case of differences the specifications of this part of ISO shall have precedence. Server state error handling, e. F18A16 SystemSupplierIdentifier This value shall be used to reference the system supplier name and address information.
This information shall be provided by all servers. In addition the specified parameters Priority and ReservedBit shall 19192-4 used. It defines the data link layer’s specific implementation of the unified diagnostic communication requirements, mainly given in the ISO and ISO document series by additional requirements and restrictions specific to the implementation of UDS on an ISO network.
Signal stuck low This sub type is used for failures where the server measures a signal that remains low when transitions are expected. When mapped on this model, the communication system specified by ISO is broken down into: An example is given in Annex C.
Transport layer Layer 3: System Programming Failures This sub type is used for System Programming Failures that cannot be assigned to a specific sub type. Total execution and transmission time. Bits that are not supported by the server shall be set to 0. Please help improve this article by adding citations to reliable sources. It is used for communication between the tractor and one or more trailers. It encodes the network layer PDU type and network layer protocol control information.
Circuit short to battery This sub 1199-4 is used for failures, where the server measures vehicle system battery positive potential for greater ios a specified time period or when some other value is expected.
Figure 3 — Client service state diagram — Service request with physical server target address 2? Note that once this bit is set to ‘1’, it shall remain a ‘1’ until a new monitoring cycle is started. Signal incorrect after event This sub type is used for failures where the server does not see the correct change of a parameter or group of isk in response to a particular event. Functions, services and protocols of the layers 1 to 4 shall be identical for basic diagnostics and enhanced diagnostics.
Following a service request with a functional server target address the time ACT3. An error condition, e. A following service response from the application shall be executed.
The functional addresses of the data link between towing and towed vehicle and of the local trailer network shall be in accordance with Tables A. General failure information sub type description 58?
ISO – Wikipedia
Session layer primitives are one to one mapped on transport layer primitives and vice versa without any further action.
TestFailed result was reported at least once during the current monitoring cycle.
Adobe is a trademark of Adobe Systems Incorporated. Only one connection between two peer network layer entities shall be allowed at the same time. Client state for error handling, e. The work of preparing International Standards is normally carried out through ISO technical committees. Following a service request with a functional server target address: The physical sub-networks between towing and towed vehicles are part of the local motor vehicle network and share the same address range.
ISO consists of the following parts, under the general title Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles: Layer 3 Network layer for diagnostics. Client states while processing a diagnostic service shall be as specified in Table 2, events resulting in a client state change shall be as specified in Table 3. Please first log in with a verified email before subscribing to alerts.
Not configured This sub type is used by the server to indicate the need to enter program the sub system option content or the vehicle option content. Reset to ‘0’ after a call to ClearDiagnosticInformation. DTC test is not failed at time of request ‘1’ 2 DTC test failed at time of request U PendingDTC This bit shall indicate whether or not a diagnostic test has reported a TestFailed result at any time during the current or last completed monitoring cycle.
General Electrical Failure This sub type is used for General Electrical Failures that cannot be assigned to a specific sub type. Circuit resistance below threshold 1A16 This sub type is used for failures, where the server infers a circuit resistance below a specified range. The client shall then change to the ES state for error handling. General failure information sub type description — 8E16 — ? Find Similar Items This product falls into the following categories.
The Server has understood the service request, but it cannot execute the service at this time and will not start the service at any time later, e. Presentation layer primitives are one to one mapped on session layer primitives and vice versa without any further action.
Interchange of digital information on electrical connections between towing and towed vehicles. Wrong mounting position This sub type is used for failures where the server detects incorrectly mounted components, e.