• June 24, 2019

KSPA Transistor Datasheet pdf, KSPA Equivalent. Parameters and Characteristics. NPN Epitaxial Silicon Transistor. Absolute Maximum RS=IKΩ, f=1KHz. 4. dB. KSPA Design. This datasheet contains the design specifications for. The KSPA is manufactured in a plastic TO case. When looking at the flat side with the leads pointed downward, the three leads emerging from the.

Author: Arashizahn Mat
Country: Maldives
Language: English (Spanish)
Genre: Literature
Published (Last): 18 March 2015
Pages: 352
PDF File Size: 10.35 Mb
ePub File Size: 18.3 Mb
ISBN: 522-6-52430-822-1
Downloads: 76991
Price: Free* [*Free Regsitration Required]
Uploader: Akizilkree

The capacitors C1 and C2 are simply used for filtering purpose. Every transistor has a gain h FE associated with it, which can be used to amplify voltage or current. Transitsor as Amplifier Another Common application of ksp2222a Transistor is as amplifiers. TL — Programmable Reference Voltage. The base pin of the transistor has to be biased with a voltage; this voltage is provided by the potential divider network formed by the resistors R4 and R6.

But there are two important features that distinguish both. Normally this type of transistor will either be used as a switch or as an amplifier, both of which is discussed below.

It is ksp2222a similar to a mechanical switch but here we will control the switch using electric signals. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. There are many types jsp2222a amplifier circuits that are possible with transistor but this is the most commonly used one because it is very good in amplifying low frequency voltage signals like audio signals.


When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Again the values of the resistor mentioned above are only for reference commonly used you have to design your own transiwtor based on the application and transistor you are using.

The resistor R2 is used to limit the current though the collector of the transistor and is not mandatory. Applications General purpose NPN transistor Can be used to switch high current upto mA loads Jsp2222a can also be used in the various switching applications. One of the most default and primary function of a transistor is to act as a switch.

KSPA Datasheet(PDF) – Fairchild Semiconductor

Another Common application of a Transistor is as amplifiers. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region. The resistor R1 is called the Base resistor and is very important to drive a transistor, it limits the base current and failing to use one might damage the transistor permanently.

However this type of amplifiers have many drawback and if you are looking for some serious amplification applications then you should look into Op-Amps which are nothing but a package of many transistors put to gather with amplification as its sole purpose. So if you looking for an NPN transistor that could switch loads of higher current then KSPA might the right choice for your project.


Submitted by admin on 24 June KSPA has a gain value of tothis value determines the amplification capacity of the transistor. The vales of the Resistor in the above image are only for reference and are not accurate.

KSP2222A Datasheet

In this type of circuit, the Emitter and the Base pin of the transistor should be commonly connected to a same voltage, so we have connected it to the Ground potential using two satasheet R4 and R3. The transistor will begin to conduct when the voltage across the Base and Emitter pin exceeds 0. KSPA is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. KSPA can allow collector current upto mA and also has power dissipation of mW which can be used to drive larger loads than compared with BC