• June 20, 2019

Order Number LMN or LMAN . Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and. LMN datasheet, LMN circuit, LMN data sheet: NSC – LM/LMA Low Noise Dual Preamplifier,alldatasheet, datasheet, Datasheet search site. LMN Datasheet, LMN PDF, LMN Data sheet, LMN manual, LMN pdf, LMN, datenblatt, Electronics LMN, alldatasheet, free, datasheet.

Author: Kajigal Zulkishakar
Country: Egypt
Language: English (Spanish)
Genre: Photos
Published (Last): 17 March 2016
Pages: 380
PDF File Size: 7.86 Mb
ePub File Size: 7.92 Mb
ISBN: 719-7-55350-263-2
Downloads: 78088
Price: Free* [*Free Regsitration Required]
Uploader: Mijind

TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

You may have to modify your existing circuit a bit by adding a blocking cap or a few bias resistors to use a “normal” op-amp. I want to do a balancing circuit for the direct outs.

Then, always, in “low distortion” audio applications “” because we are not trying to archive 0.

It is made to drive one 10K volume control in the same box, not long wires, multiple loads, etc. Nov 27, This thread has been locked.

Ask a related question What is a related question? TI is a global semiconductor design and manufacturing company. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right.

The main concern is that the circuit itself should need no changing with the replacement. No license, either express or implied, by estoppel or otherwise, is granted by TI.

LM387N Datasheet

Something similar to what Audiox did with NE Go to Support forums. We are glad that we were able to resolve this issue, and will now proceed to close this thread.


Nov 24, 8: It also has sad output power. Trademarks Privacy Policy Terms of Use. Flu got me pretty seriously! Any suggestions would be appreciated. If you have further questions related to this thread, you may click “Ask a related question” below. Some unbalance at input impedance but nothing to be alarmed for your application, as input device may not be so cool.

This is an audio circuit. Sorry for not replying back after I started this thread. Ask a related question Ask a new question. I would suggest using something more modern, this part was designed to operate at high gain not stable below 10x with small input voltages, and nominal input voltage DC biased internally. Let’s look the data sheet, if it looks right there it’s time to breadboard.

However, there must be a DC path between the output and the negative input to maintain DC feedback. I haven’t seen many designs using it? Agree that ‘ should be your go-to in this case. Hi, I started planning a mod on my old console and I wanted to find an IC opamp that can run on a single supply voltage This reduces bias resistor noise contribution, allows easy single supply operation with fewer components, and provides excellent PSRR.

LM is a penny easier because it has a bias voltage built-in, so you can set the output around half-supply.

LMN Datasheet PDF – National ->Texas Instruments

Most of the typical applications shown on the datasheet can be duplicated with “normal” op-amps, but DC biasing ddatasheet need to be added. Everything you listen to has been through multiple ‘s. Content on this site may contain or be subject to specific guidelines or limitations on use.

All content and materials on this site are provided “as is”. I’ve seen wired things with this though, but nobody says so in the data sheet, for example, lower offset working input voltage close to lower rail than at the mid point, but that’s not a good thing, I would prefer having all the time the worst case offset in most applications, at least than this, this implies a huge unlinearity and baaad CMRR!


LMN Datasheet(PDF) – National Semiconductor (TI)

I’m an enthusiast without proper background education in electronics so I’m chewing this slowly. Use of the information on this site may require a license from a third party, or a license from TI. It was an OK part for back then, ddatasheet I am surprised they still sell them.

Do you have another question? Mentions Tags More Cancel. Ask a new question Ask a new question Cancel. Due to the holidays, responses may be delayed. Thanks for your wise replies! The newly created question will be automatically linked to this question.

The LM has a different pin-out not normally used with dual op-amps – so any board layouts would have to change.

The LMN has been obsoleted.

LM387N replacement OP AMP

There are other things that usually are associated with it which is good to appear on the data sheet, for example input beyond the rails or rail to rail output, or one rail inside or close to the output range which are useful to know, but single supply, dual supply? But two 10K resistors and a 47u cap do the same.

JohnRoberts on September 06, I never understood quite well the single supply thing on opamps, usually your opamps don’t refer anything to ground, I mean, there isn’t any pin from it connected to ground, so it knows if it has a dual or single rails. Is it noisy, frequency impaired or something like that?

If I don’t know how it works, I prefer don’t turn it on. If you have a related question, please click the ” Ask a related question ” button in the top right corner.

Should I use it?